Matrix SETU ATA211 SIP-FXS-FXO Bedienungsanleitung PDF herunterladen (Seite 4)

Auto Configuration

SETU ATA can be configured automatically by retrieving its

configuration file from an Auto-Configuration Server (ACS). When

user connects SETU ATA to the network; it automatically downloads

its configuration files using TFTP, HTTP or HTTPS. This plug-n-play

feature requires the user to enter only the server address provided by

the service provider.

Auto PSTN Fall back

PSTN can be interfaced to the SETU ATA using FXO Port. This port is

used to dial out numbers to the PSTN Network. When Routing the

calls from PSTN number to SIP trunk, it may happen that the Ethernet

Link may go down or the SIP Account used is not registered. So the

call will not be routed through SIP and you will get error tone. To

avoid this you can use this feature to automatically route the call

through the FXO Port.

Automatic Number Translation

SETU ATA supports multiple port types like FXO, FXS, SIP and GSM.

Whenever a number is dialed from any of these ports, gateway

routes the call to the desired destination port as per the routing

mechanism defined for that port. In certain cases, the dialed number

string is not understood by the network through which the call is to

be routed, so by using Automatic Number Translation the dialed

number string is translated into a number that is understood by the

network or ITSP to reach the desired destination port.

Call Progress Tones and Rings

Matrix SETU ATA supports programmable tones and rings to match

those of the country where it is installed.

CLIP

SETU ATA allows users to program the FXS ports for any of the three

CLIP protocols - DTMF, FSK ITU-T V.23 and FSK Bellcore 202A.

Dialed Number Table

Matrix SETU ATA provides a list of programmable numbers or part-

numbers with the preferred SIP account for each entry. When the

user dials a number, the SETU ATA finds the matching number using

the “best-fit” logic. It then uses the SIP account given against this

matching number to make that call. This ensures lowest cost for all

the outgoing calls.

Disconnect Signaling

When a call is released from the other side of the network, the Matrix

SETU ATA can propagate this call release on the FXS in the form of

disconnect signal. The device senses this signal and frees the FXS

port.

Fax over IP (FoIP)

The user can send and receive Fax over SIP account, once a Fax

machine is connected to SETU ATA. The SETU ATA supports FoIP

using T.38 UDPTL and Pass-Through.

FXO

SETU ATA FXO port should be connected to the PSTN or PBX so that

the user can make PSTN calls from the FXO port.

International Mobile Equipment Identity (IMEI) Number

International Mobile Equipment Identity (IMEI) number provided on

SETU ATA211G GSM engine is a unique 15 digit code to identify the

GSM port. This number can be used to associate and tie the

equipment with a particular GSM network.

Web based Programming Tool

Flexible and user friendly windows based GUI software helps in

programming the features through web browser. This web based

programming feature helps users to configure the SETU ATA from any

part of the world once it is connected with the IP network.

MAC Cloning

When replacing the existing hardware with a new one, one can simplify

the installation process by simply copying the WAN associated MAC

Address to the new hardware. Thereby, eliminate the delay involved in

the setup process by informing the service provider of the newly

installed equipment.

Network Selection

SETU ATA211G provides flexibility to register with a GSM network

manually or automatically. This is useful when the installation is close

to a state or national border where local and foreign GSM networks

overlap. Programming the ATA to work only with selected network

prevents it from registering with an overlapping foreign network.

Multi-Stage Dialing

Multi-Stage Dialing is useful for ATAs connected to a SIP Server used

for networking PBX of multiple sites. The user can dial the entire

number string, both the destination number and extension number of

the destination PBX together. The ATA will split the string into two

stages, and dial out the destination number first and on receiving the

answering signal it dials the extension number. This ensures hassle

free access to PBX extension.

Peer-to-Peer Calling

SETU ATA can make and receive calls from other VoIP users without

any Registrar or Proxy server. Numbers and IP addresses can be

assigned to the other VoIP users to provide direct access across the

network. For Peer-to-Peer calling, SETU ATA provides two options - (i)

Peer-to-Peer Number Dialing (ii) IP Address Dialing. Organizations

having multiple locations like branch offices and factories can use this

feature to provide direct dialing between the dispersed end-points.

PIN Authentication

Incoming calls on FXS, FXO, SIP or GSM ports of the ATA can be

restricted to a specific caller. The caller has to first prove his

authentication before calling to ATA. This feature is used to avoid the

possibility of malicious calls and to avoid misuse of its services.

PPPoE

Matrix SETU ATA supports PPPoE client and hence can be used with

any xDSL modems.

KEY FEATURES

1 2 3 4 5 6 7 8

Kommentare zu diesen Handbüchern

Keine Kommentare

Matrix SETU ATA211 SIP-FXS-FXO Bedienungsanleitung Seite 4

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Gateways / Controller Matrix SETU ATA211 SIP-FXS-FXO